Eaton HCM1A0503-6R8-R 6.8 uH Shielded Automotive Inductor
Eaton HCM1A0503-6R8-R 6.8 uH Shielded Automotive Inductor

Eaton HCM1A0503-6R8-R 6.8 uH Shielded Automotive Inductor

Share
Eaton HCM1A0503-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 2.3 A Irms, Isat 3.8 A, DCR 81 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-6R8-R 6.8 uH Shielded Automotive Inductor

    HCM1A0503-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 2.3 A Irms, Isat 3.8 A (20% rolloff @ +25 °C), DCR 81 mOhm, 5.5 x 5.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.4 uH
    Irms (DC, 40 °C rise)2.3 A
    Isat (20% rolloff @ +25 °C)3.8 A
    DCR typical @ +20 °C81 mOhm
    DCR maximum @ +20 °C97.2 mOhm
    K-factor (Bp-p = K x L x dI)212, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Outline Drawing

    HCM1A0503-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.428 W from a typical DCR of 81 mOhm at 2.3 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 49.1 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 212, a peak-to-peak ripple of one amp produces roughly 1,442 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0503 family spans 0.2 uH to 10 uH; this row sits at position 14 of 15.

    Compared with its neighbours in the table, HCM1A0503-100-R trades 0.4 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 97.2 mOhm becomes roughly 149 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products