Eaton HCM1A0503-R68-R 0.68 uH Shielded Automotive Inductor
Eaton HCM1A0503-R68-R 0.68 uH Shielded Automotive Inductor

Eaton HCM1A0503-R68-R 0.68 uH Shielded Automotive Inductor

Share
Eaton HCM1A0503-R68-R: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 8 A Irms, Isat 12 A, DCR 8.2 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCM1A0503-R68-R 0.68 uH Shielded Automotive Inductor

    HCM1A0503-R68-R at a glance: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 8 A Irms, Isat 12 A (20% rolloff @ +25 °C), DCR 8.2 mOhm, 5.5 x 5.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.435 uH
    Irms (DC, 40 °C rise)8 A
    Isat (20% rolloff @ +25 °C)12 A
    DCR typical @ +20 °C8.2 mOhm
    DCR maximum @ +20 °C9.1 mOhm
    K-factor (Bp-p = K x L x dI)713, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10547

    Mechanical Drawing

    HCM1A0503-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10547: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 8.2 mOhm typical, the I-squared-R loss at the full 8 A rating is about 0.525 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 49 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 713 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 485 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0503 line-up this part is number 6 of 15 by inductance, between 0.2 uH and 10 uH.

    Compared with its neighbours in the table, HCM1A0503-R75-R trades 1.4 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 9.1 mOhm becomes roughly 13.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products