
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0503V3-100-R |
| OCL (open circuit inductance) | 10 uH ±20% |
| FLL minimum, at Isat | 6.4 uH |
| Irms (DC, 40 °C rise) | 2.8 A |
| Isat (20% rolloff @ +25 °C) | 2.3 A |
| DCR typical @ +20 °C | 90 mOhm |
| DCR maximum @ +20 °C | 108 mOhm |
| SRF typical | 13 MHz |
| K-factor (Bp-p = K x L x dI) | 188, Bp-p in Gauss |
| Package | 5.7 x 5.4 mm |
| Height | 3.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1483 |

Drawing reproduced from Eaton Technical Data ELX1483: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.
The DCR figure of 90 mOhm is what sets the efficiency: at 2.8 A the winding drops about 0.252 mV and dissipates 0.706 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
Energy storage at the saturation current is around 26.4 uJ, the number that connects the inductance and the current rating into a single transient figure.
The K-factor of 188 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,880 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 13 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
The HCM1A0503V3 family spans 0.2 uH to 10 uH; this row sits at position 15 of 15.
One step down the table, HCM1A0503V3-6R8-R, sits at 6.8 uH with 3.3 A and 61 mOhm – the lower inductance buys about 0 A of extra current in the same body.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 108 mOhm becomes roughly 165 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd