Eaton HCM1A0503V3-1R0-R 1.0 uH Shielded Automotive Inductor
Eaton HCM1A0503V3-1R0-R 1.0 uH Shielded Automotive Inductor

Eaton HCM1A0503V3-1R0-R 1.0 uH Shielded Automotive Inductor

Share
Eaton HCM1A0503V3-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 8.4 A Irms, Isat 8.5 A, DCR 10 mOhm, 5.7 x 5.4 mm.
    • Product Details
    • Download

    Eaton HCM1A0503V3-1R0-R 1.0 uH Shielded Automotive Inductor

    HCM1A0503V3-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 8.4 A Irms, Isat 8.5 A (20% rolloff @ +25 °C), DCR 10 mOhm, 5.7 x 5.4 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503V3-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)8.4 A
    Isat (20% rolloff @ +25 °C)8.5 A
    DCR typical @ +20 °C10 mOhm
    DCR maximum @ +20 °C11.4 mOhm
    SRF typical53 MHz
    K-factor (Bp-p = K x L x dI)603, Bp-p in Gauss
    Package5.7 x 5.4 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1483

    Mechanical Dimensions & Pad Layout

    HCM1A0503V3-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1483: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 8.4 A the winding dissipates about 0.706 W in copper alone, using the typical DCR of 10 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 36.1 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 603 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 603 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 53 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0503V3 line-up this part is number 8 of 15 by inductance, between 0.2 uH and 10 uH.

    The next value up in the same family, HCM1A0503V3-1R5-R, gives 1.5 uH at 6.2 A and DCR 15.4 mOhm: the extra inductance costs about 3.8 A of rated current.

    • Core material: alloy powder core, 5.7 x 5.4 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.4 mOhm becomes roughly 17.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products