Eaton HCM1A0503V3-2R2-R 2.2 uH Automotive Power Inductor
Eaton HCM1A0503V3-2R2-R 2.2 uH Automotive Power Inductor

Eaton HCM1A0503V3-2R2-R 2.2 uH Automotive Power Inductor

Share
Eaton HCM1A0503V3-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 5.5 A Irms, Isat 6.4 A, DCR 20 mOhm, 5.7 x 5.4 mm.
    • Product Details
    • Download

    Eaton HCM1A0503V3-2R2-R 2.2 uH Automotive Power Inductor

    HCM1A0503V3-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 5.5 A Irms, Isat 6.4 A (20% rolloff @ +25 °C), DCR 20 mOhm, 5.7 x 5.4 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503V3-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.4 uH
    Irms (DC, 40 °C rise)5.5 A
    Isat (20% rolloff @ +25 °C)6.4 A
    DCR typical @ +20 °C20 mOhm
    DCR maximum @ +20 °C23 mOhm
    SRF typical33 MHz
    K-factor (Bp-p = K x L x dI)371, Bp-p in Gauss
    Package5.7 x 5.4 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1483

    Mechanical Drawing

    HCM1A0503V3-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1483: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 5.5 A the winding dissipates about 0.605 W in copper alone, using the typical DCR of 20 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 45.1 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 371 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 816 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 33 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 15 values listed for HCM1A0503V3, this is the 10th, in a family covering 0.2 uH to 10 uH.

    The next value up in the same family, HCM1A0503V3-3R3-R, gives 3.3 uH at 4.7 A and DCR 32 mOhm: the extra inductance costs about 1.5 A of rated current.

    • Core material: alloy powder core, 5.7 x 5.4 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 23 mOhm becomes roughly 35.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products