Eaton HCM1A0503V3-3R3-R 3.3 uH AEC-Q200 Inductor, 4.7 A
Eaton HCM1A0503V3-3R3-R 3.3 uH AEC-Q200 Inductor, 4.7 A

Eaton HCM1A0503V3-3R3-R 3.3 uH AEC-Q200 Inductor, 4.7 A

Share
Eaton HCM1A0503V3-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 4.7 A Irms, Isat 6.5 A, DCR 32 mOhm, 5.7 x 5.4 mm.
    • Product Details
    • Download

    Eaton HCM1A0503V3-3R3-R 3.3 uH AEC-Q200 Inductor, 4.7 A

    HCM1A0503V3-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 4.7 A Irms, Isat 6.5 A (20% rolloff @ +25 °C), DCR 32 mOhm, 5.7 x 5.4 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0503V3-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.1 uH
    Irms (DC, 40 °C rise)4.7 A
    Isat (20% rolloff @ +25 °C)6.5 A
    DCR typical @ +20 °C32 mOhm
    DCR maximum @ +20 °C38 mOhm
    SRF typical25 MHz
    K-factor (Bp-p = K x L x dI)308, Bp-p in Gauss
    Package5.7 x 5.4 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1483

    Mechanical Drawing

    HCM1A0503V3-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1483: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 4.7 A the winding dissipates about 0.707 W in copper alone, using the typical DCR of 32 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 69.7 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 308 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,016 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 25 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0503V3 line-up this part is number 11 of 15 by inductance, between 0.2 uH and 10 uH.

    Compared with its neighbours in the table, HCM1A0503V3-4R7-R trades 1.4 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 5.7 x 5.4 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 38 mOhm becomes roughly 58.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products