Eaton HCM1A0703-1R0-R 1.0 uH Automotive Power Inductor
Eaton HCM1A0703-1R0-R 1.0 uH Automotive Power Inductor

Eaton HCM1A0703-1R0-R 1.0 uH Automotive Power Inductor

Share
Eaton HCM1A0703-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 7.9 A Irms, Isat 13 A, DCR 9 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-1R0-R 1.0 uH Automotive Power Inductor

    HCM1A0703-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 7.9 A Irms, Isat 13 A (20% rolloff @ +25 °C), DCR 9 mOhm, 7.4 x 7 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0703-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)7.9 A
    Isat (20% rolloff @ +25 °C)13 A
    DCR typical @ +20 °C9 mOhm
    DCR maximum @ +20 °C10 mOhm
    K-factor (Bp-p = K x L x dI)450, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Outline Drawing

    HCM1A0703-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    With 9 mOhm typical, the I-squared-R loss at the full 7.9 A rating is about 0.562 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 84.5 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 450 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 450 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 19 values listed for HCM1A0703, this is the 9th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A0703-1R2-R, gives 1.2 uH at 7.8 A and DCR 9.3 mOhm: the extra inductance costs about 0.7 A of rated current.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 10 mOhm becomes roughly 15.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products