Eaton HCM1A0703-8R2-R 8.2 uH Shielded Automotive Inductor
Eaton HCM1A0703-8R2-R 8.2 uH Shielded Automotive Inductor

Eaton HCM1A0703-8R2-R 8.2 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703-8R2-R: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 3.1 A Irms, Isat 5.6 A, DCR 64 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-8R2-R 8.2 uH Shielded Automotive Inductor

    HCM1A0703-8R2-R at a glance: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 3.1 A Irms, Isat 5.6 A (20% rolloff @ +25 °C), DCR 64 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0703-8R2-R
    OCL (open circuit inductance)8.2 uH ±20%
    FLL minimum, at Isat5.2 uH
    Irms (DC, 40 °C rise)3.1 A
    Isat (20% rolloff @ +25 °C)5.6 A
    DCR typical @ +20 °C64 mOhm
    DCR maximum @ +20 °C68 mOhm
    K-factor (Bp-p = K x L x dI)159, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Mechanical Drawing

    HCM1A0703-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 64 mOhm is what sets the efficiency: at 3.1 A the winding drops about 0.198 mV and dissipates 0.615 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 129 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 159 means the flux swing is about 1,304 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 19 values listed for HCM1A0703, this is the 15th, in a family covering 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCM1A0703-100-R trades 0.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 68 mOhm becomes roughly 104 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products