Eaton HCM1A0703-R33-R AEC-Q200 Inductor 0.33 uH, Isat 19 A
Eaton HCM1A0703-R33-R AEC-Q200 Inductor 0.33 uH, Isat 19 A

Eaton HCM1A0703-R33-R AEC-Q200 Inductor 0.33 uH, Isat 19 A

Share
Eaton HCM1A0703-R33-R: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 14 A Irms, Isat 19 A, DCR 3.5 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCM1A0703-R33-R AEC-Q200 Inductor 0.33 uH, Isat 19 A

    HCM1A0703-R33-R at a glance: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 14 A Irms, Isat 19 A (20% rolloff @ +25 °C), DCR 3.5 mOhm, 7.4 x 7 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0703-R33-R
    OCL (open circuit inductance)0.33 uH ±20%
    FLL minimum, at Isat0.21 uH
    Irms (DC, 40 °C rise)14 A
    Isat (20% rolloff @ +25 °C)19 A
    DCR typical @ +20 °C3.5 mOhm
    DCR maximum @ +20 °C4 mOhm
    K-factor (Bp-p = K x L x dI)907, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10548

    Outline Drawing

    HCM1A0703-R33-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10548: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.686 W from a typical DCR of 3.5 mOhm at 14 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 59.6 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 907, a peak-to-peak ripple of one amp produces roughly 299 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0703 family this is value 4 of 19, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCM1A0703-R22-R, sits at 0.22 uH with 17 A and 2.3 mOhm – the lower inductance buys about 5 A of extra current in the same body.

    • Core material: alloy powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4 mOhm becomes roughly 6.12 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products