Eaton HCM1A0703V2-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A
Eaton HCM1A0703V2-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

Eaton HCM1A0703V2-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

Share
Eaton HCM1A0703V2-330-R: AEC-Q200 automotive power inductor, 33 uH ±20%, 1.6 A Irms, Isat 2.3 A, DCR 200 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V2-330-R AEC-Q200 Inductor 33 uH, Isat 2.3 A

    HCM1A0703V2-330-R at a glance: AEC-Q200 automotive power inductor, 33 uH ±20%, 1.6 A Irms, Isat 2.3 A (20% rolloff @ +25 °C), DCR 200 mOhm, 7.3 x 6.8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0703V2-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat19.8 uH
    Irms (DC, 40 °C rise)1.6 A
    Isat (20% rolloff @ +25 °C)2.3 A
    DCR typical @ +20 °C200 mOhm
    DCR maximum @ +20 °C242 mOhm
    SRF typical6.5 MHz
    K-factor (Bp-p = K x L x dI)92, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10911

    Outline Drawing

    HCM1A0703V2-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10911: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 1.6 A the winding dissipates about 0.512 W in copper alone, using the typical DCR of 200 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 87.3 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    K-factor 92 means the flux swing is about 3,036 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 6.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A0703V2, this is the 20th, in a family covering 0.1 uH to 33 uH.

    One step down the table, HCM1A0703V2-220-R, sits at 22 uH with 2 A and 135 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 242 mOhm becomes roughly 370 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products