
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0703V3-100-R |
| OCL (open circuit inductance) | 10 uH ±20% |
| FLL minimum, at Isat | 6.4 uH |
| Irms (DC, 40 °C rise) | 3.3 A |
| Isat (20% rolloff @ +25 °C) | 4.4 A |
| DCR typical @ +20 °C | 65 mOhm |
| DCR maximum @ +20 °C | 75 mOhm |
| SRF typical | 12 MHz |
| K-factor (Bp-p = K x L x dI) | 228, Bp-p in Gauss |
| Package | 7.3 x 6.8 mm |
| Height | 3.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1484 |

Drawing reproduced from Eaton Technical Data ELX1484: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
The DCR figure of 65 mOhm is what sets the efficiency: at 3.3 A the winding drops about 0.214 mV and dissipates 0.708 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.
The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.
The core stores roughly 96.8 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.
The K-factor of 228 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,280 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 12 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Within the HCM1A0703V3 family this is value 17 of 20, in a range that runs from 0.1 uH to 33 uH.
The next value up in the same family, HCM1A0703V3-150-R, gives 15 uH at 2.6 A and DCR 96 mOhm: the extra inductance costs about 0.9 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 75 mOhm becomes roughly 115 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd