Eaton HCM1A0703V3-6R8-R 6.8 uH Shielded Automotive Inductor
Eaton HCM1A0703V3-6R8-R 6.8 uH Shielded Automotive Inductor

Eaton HCM1A0703V3-6R8-R 6.8 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703V3-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 3.6 A Irms, Isat 5.6 A, DCR 54 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-6R8-R 6.8 uH Shielded Automotive Inductor

    HCM1A0703V3-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 3.6 A Irms, Isat 5.6 A (20% rolloff @ +25 °C), DCR 54 mOhm, 7.3 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.3 uH
    Irms (DC, 40 °C rise)3.6 A
    Isat (20% rolloff @ +25 °C)5.6 A
    DCR typical @ +20 °C54 mOhm
    DCR maximum @ +20 °C65 mOhm
    SRF typical16 MHz
    K-factor (Bp-p = K x L x dI)215, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Mechanical Drawing

    HCM1A0703V3-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    At the rated 3.6 A the winding dissipates about 0.7 W in copper alone, using the typical DCR of 54 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 107 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 215 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,462 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 16 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0703V3 family this is value 15 of 20, in a range that runs from 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCM1A0703V3-8R2-R trades 0.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 65 mOhm becomes roughly 99.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products