Eaton HCM1A0703V3-R15-R 0.15 uH AEC-Q200 Inductor, 24 A
Eaton HCM1A0703V3-R15-R 0.15 uH AEC-Q200 Inductor, 24 A

Eaton HCM1A0703V3-R15-R 0.15 uH AEC-Q200 Inductor, 24 A

Share
Eaton HCM1A0703V3-R15-R: AEC-Q200 automotive power inductor, 0.15 uH ±20%, 24 A Irms, Isat 30 A, DCR 1.03 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-R15-R 0.15 uH AEC-Q200 Inductor, 24 A

    HCM1A0703V3-R15-R at a glance: AEC-Q200 automotive power inductor, 0.15 uH ±20%, 24 A Irms, Isat 30 A (20% rolloff @ +25 °C), DCR 1.03 mOhm, 7.3 x 6.8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0703V3-R15-R
    OCL (open circuit inductance)0.15 uH ±20%
    FLL minimum, at Isat0.09 uH
    Irms (DC, 40 °C rise)24 A
    Isat (20% rolloff @ +25 °C)30 A
    DCR typical @ +20 °C1.03 mOhm
    DCR maximum @ +20 °C1.3 mOhm
    SRF typical195 MHz
    K-factor (Bp-p = K x L x dI)1,923, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Outline Drawing

    HCM1A0703V3-R15-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.593 W from a typical DCR of 1.03 mOhm at 24 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 67.5 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 1,923 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 288 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 195 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A0703V3, this is the 2th, in a family covering 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCM1A0703V3-R22-R trades 11 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.3 mOhm becomes roughly 1.99 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products