Eaton HCM1A0703V3-R56-R 0.56 uH AEC-Q200 Inductor, 13 A
Eaton HCM1A0703V3-R56-R 0.56 uH AEC-Q200 Inductor, 13 A

Eaton HCM1A0703V3-R56-R 0.56 uH AEC-Q200 Inductor, 13 A

Share
Eaton HCM1A0703V3-R56-R: AEC-Q200 automotive power inductor, 0.56 uH ±20%, 13 A Irms, Isat 12 A, DCR 3.8 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-R56-R 0.56 uH AEC-Q200 Inductor, 13 A

    HCM1A0703V3-R56-R at a glance: AEC-Q200 automotive power inductor, 0.56 uH ±20%, 13 A Irms, Isat 12 A (20% rolloff @ +25 °C), DCR 3.8 mOhm, 7.3 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-R56-R
    OCL (open circuit inductance)0.56 uH ±20%
    FLL minimum, at Isat0.35 uH
    Irms (DC, 40 °C rise)13 A
    Isat (20% rolloff @ +25 °C)12 A
    DCR typical @ +20 °C3.8 mOhm
    DCR maximum @ +20 °C4.5 mOhm
    SRF typical60 MHz
    K-factor (Bp-p = K x L x dI)690, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Outline Drawing

    HCM1A0703V3-R56-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 3.8 mOhm is what sets the efficiency: at 13 A the winding drops about 0.049 mV and dissipates 0.642 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 40.3 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 690 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 386 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 60 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0703V3 line-up this part is number 6 of 20 by inductance, between 0.1 uH and 33 uH.

    Compared with its neighbours in the table, HCM1A0703V3-R68-R trades 1 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4.5 mOhm becomes roughly 6.89 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products