Eaton HCM1A0703V3-R68-R 0.68 uH Shielded Automotive Inductor
Eaton HCM1A0703V3-R68-R 0.68 uH Shielded Automotive Inductor

Eaton HCM1A0703V3-R68-R 0.68 uH Shielded Automotive Inductor

Share
Eaton HCM1A0703V3-R68-R: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 12 A Irms, Isat 13 A, DCR 4.8 mOhm, 7.3 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCM1A0703V3-R68-R 0.68 uH Shielded Automotive Inductor

    HCM1A0703V3-R68-R at a glance: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 12 A Irms, Isat 13 A (20% rolloff @ +25 °C), DCR 4.8 mOhm, 7.3 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A0703V3-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.43 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)13 A
    DCR typical @ +20 °C4.8 mOhm
    DCR maximum @ +20 °C5.5 mOhm
    SRF typical57 MHz
    K-factor (Bp-p = K x L x dI)653, Bp-p in Gauss
    Package7.3 x 6.8 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1484

    Dimensions and Pad Layout

    HCM1A0703V3-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1484: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    With 4.8 mOhm typical, the I-squared-R loss at the full 12 A rating is about 0.691 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 57.5 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 653, a peak-to-peak ripple of one amp produces roughly 444 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 57 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0703V3 line-up this part is number 7 of 20 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCM1A0703V3-R56-R, sits at 0.56 uH with 13 A and 3.8 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: alloy powder core, 7.3 x 6.8 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 5.5 mOhm becomes roughly 8.42 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products