Eaton HCM1A0805-100-R 10 uH Automotive Power Inductor
Eaton HCM1A0805-100-R 10 uH Automotive Power Inductor

Eaton HCM1A0805-100-R 10 uH Automotive Power Inductor

Share
Eaton HCM1A0805-100-R: AEC-Q200 automotive power inductor, 10 uH ±20%, 2.8 A Irms, Isat 8 A, DCR 50 mOhm, 8.3 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805-100-R 10 uH Automotive Power Inductor

    HCM1A0805-100-R at a glance: AEC-Q200 automotive power inductor, 10 uH ±20%, 2.8 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 50 mOhm, 8.3 x 8 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A0805-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)2.8 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C50 mOhm
    DCR maximum @ +20 °C55 mOhm
    K-factor (Bp-p = K x L x dI)48, Bp-p in Gauss
    Package8.3 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10549

    Dimensions and Pad Layout

    HCM1A0805-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10549: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.392 W from a typical DCR of 50 mOhm at 2.8 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 320 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 48 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 480 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0805 family spans 3.3 uH to 47 uH; this row sits at position 3 of 6.

    One step down the table, HCM1A0805-4R7-R, sits at 4.7 uH with 5.7 A and 17 mOhm – the lower inductance buys about 3.2 A of extra current in the same body.

    • Core material: alloy powder core, 8.3 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 55 mOhm becomes roughly 84.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message