Eaton HCM1A0805V2-150-R 15 uH Shielded Automotive Inductor
Eaton HCM1A0805V2-150-R 15 uH Shielded Automotive Inductor

Eaton HCM1A0805V2-150-R 15 uH Shielded Automotive Inductor

Share
Eaton HCM1A0805V2-150-R: AEC-Q200 automotive power inductor, 15 uH ±20%, 4 A Irms, Isat 4.6 A, DCR 43 mOhm, 8.4 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V2-150-R 15 uH Shielded Automotive Inductor

    HCM1A0805V2-150-R at a glance: AEC-Q200 automotive power inductor, 15 uH ±20%, 4 A Irms, Isat 4.6 A (20% rolloff @ +25 °C), DCR 43 mOhm, 8.4 x 8 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0805V2-150-R
    OCL (open circuit inductance)15 uH ±20%
    FLL minimum, at Isat9.6 uH
    Irms (DC, 40 °C rise)4 A
    Isat (20% rolloff @ +25 °C)4.6 A
    DCR typical @ +20 °C43 mOhm
    DCR maximum @ +20 °C52 mOhm
    SRF typical8 MHz
    K-factor (Bp-p = K x L x dI)63, Bp-p in Gauss
    Package8.4 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10902

    Outline Drawing

    HCM1A0805V2-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10902: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 4 A the winding dissipates about 0.688 W in copper alone, using the typical DCR of 43 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 159 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 63, a peak-to-peak ripple of one amp produces roughly 945 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 8 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 12 values listed for HCM1A0805V2, this is the 9th, in a family covering 0.22 uH to 47 uH.

    One step down the table, HCM1A0805V2-100-R, sits at 10 uH with 4 A and 49 mOhm – the lower inductance buys about 0.5 A of extra current in the same body.

    • Core material: alloy powder core, 8.4 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 52 mOhm becomes roughly 79.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products