Eaton HCM1A0805V2-330-R 33 uH Automotive Power Inductor
Eaton HCM1A0805V2-330-R 33 uH Automotive Power Inductor

Eaton HCM1A0805V2-330-R 33 uH Automotive Power Inductor

Share
Eaton HCM1A0805V2-330-R: AEC-Q200 automotive power inductor, 33 uH ±20%, 2.7 A Irms, Isat 4 A, DCR 103 mOhm, 8.4 x 8 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V2-330-R 33 uH Automotive Power Inductor

    HCM1A0805V2-330-R at a glance: AEC-Q200 automotive power inductor, 33 uH ±20%, 2.7 A Irms, Isat 4 A (20% rolloff @ +25 °C), DCR 103 mOhm, 8.4 x 8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0805V2-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat21 uH
    Irms (DC, 40 °C rise)2.7 A
    Isat (20% rolloff @ +25 °C)4 A
    DCR typical @ +20 °C103 mOhm
    DCR maximum @ +20 °C125 mOhm
    SRF typical5.5 MHz
    K-factor (Bp-p = K x L x dI)48, Bp-p in Gauss
    Package8.4 x 8 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10902

    Dimensions and Pad Layout

    HCM1A0805V2-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10902: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 103 mOhm typical, the I-squared-R loss at the full 2.7 A rating is about 0.751 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 264 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 48 means the flux swing is about 1,584 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 5.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A0805V2 family spans 0.22 uH to 47 uH; this row sits at position 11 of 12.

    One step down the table, HCM1A0805V2-220-R, sits at 22 uH with 3.5 A and 60.7 mOhm – the lower inductance buys about 1 A of extra current in the same body.

    • Core material: alloy powder core, 8.4 x 8 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 125 mOhm becomes roughly 191 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products