Eaton HCM1A0805V3-101-R 100 uH AEC-Q200 Inductor, 1.8 A
Eaton HCM1A0805V3-101-R 100 uH AEC-Q200 Inductor, 1.8 A

Eaton HCM1A0805V3-101-R 100 uH AEC-Q200 Inductor, 1.8 A

Share
Eaton HCM1A0805V3-101-R: AEC-Q200 automotive power inductor, 100 uH ±20%, 1.8 A Irms, Isat 3.3 A, DCR 310 mOhm, 8 x 7.5 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V3-101-R 100 uH AEC-Q200 Inductor, 1.8 A

    HCM1A0805V3-101-R at a glance: AEC-Q200 automotive power inductor, 100 uH ±20%, 1.8 A Irms, Isat 3.3 A (20% rolloff @ +25 °C), DCR 310 mOhm, 8 x 7.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0805V3-101-R
    OCL (open circuit inductance)100 uH ±20%
    FLL minimum, at Isat56 uH
    Irms1 (DC, 40 °C rise)1.8 A
    Irms2 (DC, 40 °C rise)1.4 A
    Isat (20% rolloff @ +25 °C)3.3 A
    DCR maximum @ +20 °C310 mOhm
    SRF typical2 MHz
    K-factor (Bp-p = K x L x dI)29, Bp-p in Gauss
    Package8 x 7.5 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1485

    Mechanical Drawing

    HCM1A0805V3-101-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1485: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 310 mOhm typical, the I-squared-R loss at the full 1.8 A rating is about 1 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 544 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 29 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,900 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Two Irms columns are quoted because two self-heating levels are allowed: 1.8 A and 1.4 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.

    Self-resonant frequency is 2 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0805V3 family this is value 14 of 14, in a range that runs from 0.22 uH to 100 uH.

    Compared with its neighbours in the table, HCM1A0805V3-680-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 8 x 7.5 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 310 mOhm becomes roughly 474 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products