Eaton HCM1A0805V3-220-R 22 uH AEC-Q200 Inductor, 3.5 A
Eaton HCM1A0805V3-220-R 22 uH AEC-Q200 Inductor, 3.5 A

Eaton HCM1A0805V3-220-R 22 uH AEC-Q200 Inductor, 3.5 A

Share
Eaton HCM1A0805V3-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 3.5 A Irms, Isat 4 A, DCR 70 mOhm, 8 x 7.5 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V3-220-R 22 uH AEC-Q200 Inductor, 3.5 A

    HCM1A0805V3-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 3.5 A Irms, Isat 4 A (20% rolloff @ +25 °C), DCR 70 mOhm, 8 x 7.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A0805V3-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14 uH
    Irms1 (DC, 40 °C rise)3.5 A
    Irms2 (DC, 40 °C rise)3.1 A
    Isat (20% rolloff @ +25 °C)4 A
    DCR maximum @ +20 °C70 mOhm
    SRF typical7.5 MHz
    K-factor (Bp-p = K x L x dI)52, Bp-p in Gauss
    Package8 x 7.5 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1485

    Mechanical Dimensions & Pad Layout

    HCM1A0805V3-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1485: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 70 mOhm typical, the I-squared-R loss at the full 3.5 A rating is about 0.858 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 176 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 52 means the flux swing is about 1,144 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Two Irms columns are quoted because two self-heating levels are allowed: 3.5 A and 3.1 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.

    Self-resonant frequency is 7.5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A0805V3 family this is value 10 of 14, in a range that runs from 0.22 uH to 100 uH.

    Compared with its neighbours in the table, HCM1A0805V3-330-R trades 1.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 8 x 7.5 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 70 mOhm becomes roughly 107 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products