
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A0805V3-3R3-R |
| OCL (open circuit inductance) | 3.3 uH ±20% |
| FLL minimum, at Isat | 2.1 uH |
| Irms1 (DC, 40 °C rise) | 10 A |
| Irms2 (DC, 40 °C rise) | 8.5 A |
| Isat (20% rolloff @ +25 °C) | 7.2 A |
| DCR maximum @ +20 °C | 10 mOhm |
| SRF typical | 21 MHz |
| K-factor (Bp-p = K x L x dI) | 159, Bp-p in Gauss |
| Package | 8 x 7.5 mm |
| Height | 5.4 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1485 |

Drawing reproduced from Eaton Technical Data ELX1485: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
Copper loss at the rated current works out to roughly 1 W from a typical DCR of 10 mOhm at 10 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
The core stores roughly 85.5 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.
With K = 159, a peak-to-peak ripple of one amp produces roughly 525 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.
Two Irms columns are quoted because two self-heating levels are allowed: 10 A and 8.5 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.
Self-resonant frequency is 21 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
In the HCM1A0805V3 line-up this part is number 6 of 14 by inductance, between 0.22 uH and 100 uH.
One step down the table, HCM1A0805V3-2R2-R, sits at 2.2 uH with 11 A and 8.5 mOhm – the lower inductance buys about 3 A of extra current in the same body.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 10 mOhm becomes roughly 15.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd