Eaton HCM1A0805V3-R47-R 0.47 uH AEC-Q200 Inductor, 21.5 A
Eaton HCM1A0805V3-R47-R 0.47 uH AEC-Q200 Inductor, 21.5 A

Eaton HCM1A0805V3-R47-R 0.47 uH AEC-Q200 Inductor, 21.5 A

Share
Eaton HCM1A0805V3-R47-R: AEC-Q200 automotive power inductor, 0.47 uH ±20%, 21.5 A Irms, Isat 26 A, DCR 2.8 mOhm, 8 x 7.5 mm.
    • Product Details
    • Download

    Eaton HCM1A0805V3-R47-R 0.47 uH AEC-Q200 Inductor, 21.5 A

    HCM1A0805V3-R47-R at a glance: AEC-Q200 automotive power inductor, 0.47 uH ±20%, 21.5 A Irms, Isat 26 A (20% rolloff @ +25 °C), DCR 2.8 mOhm, 8 x 7.5 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A0805V3-R47-R
    OCL (open circuit inductance)0.47 uH ±20%
    FLL minimum, at Isat0.3 uH
    Irms1 (DC, 40 °C rise)21.5 A
    Irms2 (DC, 40 °C rise)19 A
    Isat (20% rolloff @ +25 °C)26 A
    DCR maximum @ +20 °C2.8 mOhm
    SRF typical105 MHz
    K-factor (Bp-p = K x L x dI)295, Bp-p in Gauss
    Package8 x 7.5 mm
    Height5.4 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1485

    Dimensions and Pad Layout

    HCM1A0805V3-R47-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1485: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 2.8 mOhm is what sets the efficiency: at 21.5 A the winding drops about 0.06 mV and dissipates 1.29 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 159 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 295 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 139 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Two Irms columns are quoted because two self-heating levels are allowed: 21.5 A and 19 A for the same winding. Pick the column that matches the board’s thermal design, not the larger number.

    Self-resonant frequency is 105 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A0805V3 line-up this part is number 2 of 14 by inductance, between 0.22 uH and 100 uH.

    Compared with its neighbours in the table, HCM1A0805V3-R68-R trades 12.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 8 x 7.5 mm body at 5.4 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.8 mOhm becomes roughly 4.29 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products