Eaton HCM1A1104-R20-R 0.20 uH AEC-Q200 Inductor, 33 A
Eaton HCM1A1104-R20-R 0.20 uH AEC-Q200 Inductor, 33 A

Eaton HCM1A1104-R20-R 0.20 uH AEC-Q200 Inductor, 33 A

Share
Eaton HCM1A1104-R20-R: AEC-Q200 automotive power inductor, 0.20 uH ±20%, 33 A Irms, Isat 40 A, DCR 0.63 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104-R20-R 0.20 uH AEC-Q200 Inductor, 33 A

    HCM1A1104-R20-R at a glance: AEC-Q200 automotive power inductor, 0.20 uH ±20%, 33 A Irms, Isat 40 A (20% rolloff @ +25 °C), DCR 0.63 mOhm, 11.5 x 10.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1104-R20-R
    OCL (open circuit inductance)0.20 uH ±20%
    FLL minimum, at Isat0.13 uH
    Irms (DC, 40 °C rise)33 A
    Isat (20% rolloff @ +25 °C)40 A
    DCR typical @ +20 °C0.63 mOhm
    DCR maximum @ +20 °C0.72 mOhm
    K-factor (Bp-p = K x L x dI)902, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10550

    Mechanical Drawing

    HCM1A1104-R20-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10550: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    The DCR figure of 0.63 mOhm is what sets the efficiency: at 33 A the winding drops about 0.021 mV and dissipates 0.686 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 160 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 902, a peak-to-peak ripple of one amp produces roughly 180 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1104 family spans 0.2 uH to 100 uH; this row sits at position 1 of 19.

    One step down the table, HCM1A1104-R36-R, sits at 0.36 uH with 26 A and 1.04 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.72 mOhm becomes roughly 1.1 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products