Eaton HCM1A1104-R90-R 0.90 uH Shielded Automotive Inductor
Eaton HCM1A1104-R90-R 0.90 uH Shielded Automotive Inductor

Eaton HCM1A1104-R90-R 0.90 uH Shielded Automotive Inductor

Share
Eaton HCM1A1104-R90-R: AEC-Q200 automotive power inductor, 0.90 uH ±20%, 20 A Irms, Isat 22 A, DCR 2.17 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104-R90-R 0.90 uH Shielded Automotive Inductor

    HCM1A1104-R90-R at a glance: AEC-Q200 automotive power inductor, 0.90 uH ±20%, 20 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 2.17 mOhm, 11.5 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1104-R90-R
    OCL (open circuit inductance)0.90 uH ±20%
    FLL minimum, at Isat0.58 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C2.17 mOhm
    DCR maximum @ +20 °C2.5 mOhm
    K-factor (Bp-p = K x L x dI)309, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10550

    Dimensions and Pad Layout

    HCM1A1104-R90-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10550: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    The DCR figure of 2.17 mOhm is what sets the efficiency: at 20 A the winding drops about 0.043 mV and dissipates 0.868 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 218 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 309 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 278 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1104 family spans 0.2 uH to 100 uH; this row sits at position 6 of 19.

    Compared with its neighbours in the table, HCM1A1104-1R0-R trades 6.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.5 mOhm becomes roughly 3.83 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products