Eaton HCM1A1104V2-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 11.5 A
Eaton HCM1A1104V2-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 11.5 A

Eaton HCM1A1104V2-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 11.5 A

Share
Eaton HCM1A1104V2-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8.2 A Irms, Isat 11.5 A, DCR 9.9 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V2-3R3-R AEC-Q200 Inductor 3.3 uH, Isat 11.5 A

    HCM1A1104V2-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 8.2 A Irms, Isat 11.5 A (20% rolloff @ +25 °C), DCR 9.9 mOhm, 11.2 x 10.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1104V2-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.11 uH
    Irms (DC, 40 °C rise)8.2 A
    Isat (20% rolloff @ +25 °C)11.5 A
    DCR typical @ +20 °C9.9 mOhm
    DCR maximum @ +20 °C11.4 mOhm
    SRF typical19 MHz
    K-factor (Bp-p = K x L x dI)215, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10903

    Mechanical Drawing

    HCM1A1104V2-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10903: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.666 W from a typical DCR of 9.9 mOhm at 8.2 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 218 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 215 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 710 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 19 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1104V2 line-up this part is number 10 of 19 by inductance, between 0.2 uH and 68 uH.

    One step down the table, HCM1A1104V2-2R2-R, sits at 2.2 uH with 10.5 A and 6 mOhm – the lower inductance buys about 2.5 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.4 mOhm becomes roughly 17.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Verify the qualification and the mounting process match the assembly line.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products