Eaton HCM1A1104V2-470-R AEC-Q200 Inductor 47 uH, Isat 3.6 A
Eaton HCM1A1104V2-470-R AEC-Q200 Inductor 47 uH, Isat 3.6 A

Eaton HCM1A1104V2-470-R AEC-Q200 Inductor 47 uH, Isat 3.6 A

Share
Eaton HCM1A1104V2-470-R: AEC-Q200 automotive power inductor, 47 uH ±20%, 2.7 A Irms, Isat 3.6 A, DCR 147 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V2-470-R AEC-Q200 Inductor 47 uH, Isat 3.6 A

    HCM1A1104V2-470-R at a glance: AEC-Q200 automotive power inductor, 47 uH ±20%, 2.7 A Irms, Isat 3.6 A (20% rolloff @ +25 °C), DCR 147 mOhm, 11.2 x 10.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1104V2-470-R
    OCL (open circuit inductance)47 uH ±20%
    FLL minimum, at Isat30.1 uH
    Irms (DC, 40 °C rise)2.7 A
    Isat (20% rolloff @ +25 °C)3.6 A
    DCR typical @ +20 °C147 mOhm
    DCR maximum @ +20 °C165 mOhm
    SRF typical3.9 MHz
    K-factor (Bp-p = K x L x dI)63, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10903

    Dimensions and Pad Layout

    HCM1A1104V2-470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10903: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 147 mOhm is what sets the efficiency: at 2.7 A the winding drops about 0.397 mV and dissipates 1.07 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    At Isat the part holds about 305 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 63, a peak-to-peak ripple of one amp produces roughly 2,961 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 3.9 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 19 values listed for HCM1A1104V2, this is the 18th, in a family covering 0.2 uH to 68 uH.

    One step down the table, HCM1A1104V2-330-R, sits at 33 uH with 3.3 A and 89 mOhm – the lower inductance buys about 1.1 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 165 mOhm becomes roughly 253 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products