
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1104V2-680-R |
| OCL (open circuit inductance) | 68 uH ±20% |
| FLL minimum, at Isat | 43.5 uH |
| Irms (DC, 40 °C rise) | 2.2 A |
| Isat (20% rolloff @ +25 °C) | 3 A |
| DCR typical @ +20 °C | 190 mOhm |
| DCR maximum @ +20 °C | 210 mOhm |
| SRF typical | 3.1 MHz |
| K-factor (Bp-p = K x L x dI) | 39, Bp-p in Gauss |
| Package | 11.2 x 10.3 mm |
| Height | 4.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10903 |

Drawing reproduced from Eaton Technical Data 10903: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.
The DCR figure of 190 mOhm is what sets the efficiency: at 2.2 A the winding drops about 0.418 mV and dissipates 0.92 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
Stored energy at Isat is about 306 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
The K-factor of 39 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 2,652 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 3.1 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
The HCM1A1104V2 family spans 0.2 uH to 68 uH; this row sits at position 19 of 19.
Compared with its neighbours in the table, HCM1A1104V2-470-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 210 mOhm becomes roughly 321 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What is the operating temperature range?
The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.
Why do V2 and V3 parts exist?
They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd