Eaton HCM1A1104V2-R36-R AEC-Q200 Inductor 0.36 uH, Isat 33 A
Eaton HCM1A1104V2-R36-R AEC-Q200 Inductor 0.36 uH, Isat 33 A

Eaton HCM1A1104V2-R36-R AEC-Q200 Inductor 0.36 uH, Isat 33 A

Share
Eaton HCM1A1104V2-R36-R: AEC-Q200 automotive power inductor, 0.36 uH ±20%, 26 A Irms, Isat 33 A, DCR 1.04 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1104V2-R36-R AEC-Q200 Inductor 0.36 uH, Isat 33 A

    HCM1A1104V2-R36-R at a glance: AEC-Q200 automotive power inductor, 0.36 uH ±20%, 26 A Irms, Isat 33 A (20% rolloff @ +25 °C), DCR 1.04 mOhm, 11.2 x 10.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A1104V2-R36-R
    OCL (open circuit inductance)0.36 uH ±20%
    FLL minimum, at Isat0.23 uH
    Irms (DC, 40 °C rise)26 A
    Isat (20% rolloff @ +25 °C)33 A
    DCR typical @ +20 °C1.04 mOhm
    DCR maximum @ +20 °C1.2 mOhm
    SRF typical80 MHz
    K-factor (Bp-p = K x L x dI)493, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10903

    Mechanical Dimensions & Pad Layout

    HCM1A1104V2-R36-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10903: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    At the rated 26 A the winding dissipates about 0.703 W in copper alone, using the typical DCR of 1.04 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 196 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 493 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 178 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 80 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1104V2 family this is value 2 of 19, in a range that runs from 0.2 uH to 68 uH.

    One step down the table, HCM1A1104V2-R20-R, sits at 0.20 uH with 43 A and 0.63 mOhm – the lower inductance buys about 18 A of extra current in the same body.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.2 mOhm becomes roughly 1.84 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products