
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1104V3-R36-R |
| OCL (open circuit inductance) | 0.36 uH ±20% |
| FLL minimum, at Isat | 0.23 uH |
| Irms (DC, 40 °C rise) | 26 A |
| Isat (20% rolloff @ +25 °C) | 33 A |
| DCR typical @ +20 °C | 1.04 mOhm |
| DCR maximum @ +20 °C | 1.2 mOhm |
| SRF typical | 80 MHz |
| K-factor (Bp-p = K x L x dI) | 547, Bp-p in Gauss |
| Package | 11.2 x 10.3 mm |
| Height | 4.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1490 |

Drawing reproduced from Eaton Technical Data ELX1490: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
At the rated 26 A the winding dissipates about 0.703 W in copper alone, using the typical DCR of 1.04 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.
Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.
Stored energy at Isat is about 196 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
K-factor 547 means the flux swing is about 197 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.
Self-resonant frequency is 80 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
The HCM1A1104V3 family spans 0.2 uH to 68 uH; this row sits at position 2 of 19.
The next value up in the same family, HCM1A1104V3-R45-R, gives 0.45 uH at 25 A and DCR 1.07 mOhm: the extra inductance costs about 18 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.2 mOhm becomes roughly 1.84 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
Does the automotive grade change the electrical values?
Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd