Eaton HCM1A1105V2-1R0-R AEC-Q200 Inductor 1.0 uH, Isat 24 A
Eaton HCM1A1105V2-1R0-R AEC-Q200 Inductor 1.0 uH, Isat 24 A

Eaton HCM1A1105V2-1R0-R AEC-Q200 Inductor 1.0 uH, Isat 24 A

Share
Eaton HCM1A1105V2-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 20 A Irms, Isat 24 A, DCR 2.1 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1105V2-1R0-R AEC-Q200 Inductor 1.0 uH, Isat 24 A

    HCM1A1105V2-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 20 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 2.1 mOhm, 11.2 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1105V2-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C2.1 mOhm
    DCR maximum @ +20 °C2.4 mOhm
    SRF typical44 MHz
    K-factor (Bp-p = K x L x dI)218, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10909

    Mechanical Drawing

    HCM1A1105V2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10909: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 2.1 mOhm is what sets the efficiency: at 20 A the winding drops about 0.042 mV and dissipates 0.84 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 288 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 218 means the flux swing is about 218 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 44 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1105V2 family spans 0.68 uH to 68 uH; this row sits at position 4 of 19.

    The next value up in the same family, HCM1A1105V2-1R2-R, gives 1.2 uH at 21 A and DCR 2.1 mOhm: the extra inductance costs about 1 A of rated current.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.4 mOhm becomes roughly 3.67 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products