Eaton HCM1A1105V2-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 10 A
Eaton HCM1A1105V2-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 10 A

Eaton HCM1A1105V2-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 10 A

Share
Eaton HCM1A1105V2-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 7 A Irms, Isat 10 A, DCR 17.1 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1105V2-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 10 A

    HCM1A1105V2-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 7 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 17.1 mOhm, 11.2 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1105V2-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)7 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C17.1 mOhm
    DCR maximum @ +20 °C20 mOhm
    SRF typical11 MHz
    K-factor (Bp-p = K x L x dI)70, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10909

    Mechanical Dimensions & Pad Layout

    HCM1A1105V2-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10909: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.838 W from a typical DCR of 17.1 mOhm at 7 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 340 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 70 means the flux swing is about 476 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 11 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1105V2 line-up this part is number 12 of 19 by inductance, between 0.68 uH and 68 uH.

    Compared with its neighbours in the table, HCM1A1105V2-100-R trades 1.8 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 20 mOhm becomes roughly 30.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products