Eaton HCM1A1105V2-R72-R 0.72 uH AEC-Q200 Inductor, 23 A
Eaton HCM1A1105V2-R72-R 0.72 uH AEC-Q200 Inductor, 23 A

Eaton HCM1A1105V2-R72-R 0.72 uH AEC-Q200 Inductor, 23 A

Share
Eaton HCM1A1105V2-R72-R: AEC-Q200 automotive power inductor, 0.72 uH ±20%, 23 A Irms, Isat 24 A, DCR 1.55 mOhm, 11.2 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCM1A1105V2-R72-R 0.72 uH AEC-Q200 Inductor, 23 A

    HCM1A1105V2-R72-R at a glance: AEC-Q200 automotive power inductor, 0.72 uH ±20%, 23 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 1.55 mOhm, 11.2 x 10.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1105V2-R72-R
    OCL (open circuit inductance)0.72 uH ±20%
    FLL minimum, at Isat0.46 uH
    Irms (DC, 40 °C rise)23 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C1.55 mOhm
    DCR maximum @ +20 °C1.71 mOhm
    SRF typical54 MHz
    K-factor (Bp-p = K x L x dI)298, Bp-p in Gauss
    Package11.2 x 10.3 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10909

    Mechanical Dimensions & Pad Layout

    HCM1A1105V2-R72-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10909: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 23 A the winding dissipates about 0.82 W in copper alone, using the typical DCR of 1.55 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 207 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 298 means the flux swing is about 215 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 54 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1105V2 family this is value 2 of 19, in a range that runs from 0.68 uH to 68 uH.

    Compared with its neighbours in the table, HCM1A1105V2-R90-R trades 2.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 11.2 x 10.3 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.71 mOhm becomes roughly 2.62 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products