Eaton HCM1A1305-1R8-R 1.8 uH Shielded Automotive Inductor
Eaton HCM1A1305-1R8-R 1.8 uH Shielded Automotive Inductor

Eaton HCM1A1305-1R8-R 1.8 uH Shielded Automotive Inductor

Share
Eaton HCM1A1305-1R8-R: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 16 A Irms, Isat 20 A, DCR 4 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1A1305-1R8-R 1.8 uH Shielded Automotive Inductor

    HCM1A1305-1R8-R at a glance: AEC-Q200 automotive power inductor, 1.8 uH ±20%, 16 A Irms, Isat 20 A (20% rolloff @ +25 °C), DCR 4 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1305-1R8-R
    OCL (open circuit inductance)1.8 uH ±20%
    FLL minimum, at Isat1.15 uH
    Irms (DC, 40 °C rise)16 A
    Isat (20% rolloff @ +25 °C)20 A
    DCR typical @ +20 °C4 mOhm
    DCR maximum @ +20 °C4.6 mOhm
    K-factor (Bp-p = K x L x dI)154, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10551

    Outline Drawing

    HCM1A1305-1R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10551: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 16 A the winding dissipates about 1.02 W in copper alone, using the typical DCR of 4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 360 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 154 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 277 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 23 values listed for HCM1A1305, this is the 10th, in a family covering 0.1 uH to 33 uH.

    Compared with its neighbours in the table, HCM1A1305-2R2-R trades 3 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4.6 mOhm becomes roughly 7.04 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products