Eaton HCM1A1305-330-R AEC-Q200 Inductor 33 uH, Isat 7 A
Eaton HCM1A1305-330-R AEC-Q200 Inductor 33 uH, Isat 7 A

Eaton HCM1A1305-330-R AEC-Q200 Inductor 33 uH, Isat 7 A

Share
Eaton HCM1A1305-330-R: AEC-Q200 automotive power inductor, 33 uH ±20%, 4 A Irms, Isat 7 A, DCR 74.5 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1A1305-330-R AEC-Q200 Inductor 33 uH, Isat 7 A

    HCM1A1305-330-R at a glance: AEC-Q200 automotive power inductor, 33 uH ±20%, 4 A Irms, Isat 7 A (20% rolloff @ +25 °C), DCR 74.5 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1305-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat21.1 uH
    Irms (DC, 40 °C rise)4 A
    Isat (20% rolloff @ +25 °C)7 A
    DCR typical @ +20 °C74.5 mOhm
    DCR maximum @ +20 °C85.5 mOhm
    K-factor (Bp-p = K x L x dI)32, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10551

    Outline Drawing

    HCM1A1305-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10551: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 74.5 mOhm is what sets the efficiency: at 4 A the winding drops about 0.298 mV and dissipates 1.19 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 808 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 32, a peak-to-peak ripple of one amp produces roughly 1,056 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1305 line-up this part is number 23 of 23 by inductance, between 0.1 uH and 33 uH.

    The next value up in the same family, HCM1A1305-220-R, gives 22 uH at 3.5 A and DCR 45 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 85.5 mOhm becomes roughly 131 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message