
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1305-6R0-R |
| OCL (open circuit inductance) | 6.0 uH ±20% |
| FLL minimum, at Isat | 3.84 uH |
| Irms (DC, 40 °C rise) | 8.1 A |
| Isat (20% rolloff @ +25 °C) | 12.5 A |
| DCR typical @ +20 °C | 12.5 mOhm |
| DCR maximum @ +20 °C | 14.5 mOhm |
| K-factor (Bp-p = K x L x dI) | 90, Bp-p in Gauss |
| Package | 13.8 x 12.5 mm |
| Height | 5.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data 10551 |

Drawing reproduced from Eaton Technical Data 10551: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.
With 12.5 mOhm typical, the I-squared-R loss at the full 8.1 A rating is about 0.82 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.
The core stores roughly 469 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.
The K-factor of 90 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 540 Gauss of Bp-p, the figure the core-loss curve is plotted against.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
Within the HCM1A1305 family this is value 15 of 23, in a range that runs from 0.1 uH to 33 uH.
The next value up in the same family, HCM1A1305-6R8-R, gives 6.8 uH at 8.3 A and DCR 13 mOhm: the extra inductance costs about 0.5 A of rated current.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 14.5 mOhm becomes roughly 22.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd