Eaton HCM1A1305-R10-R 0.10 uH AEC-Q200 Inductor, 43 A
Eaton HCM1A1305-R10-R 0.10 uH AEC-Q200 Inductor, 43 A

Eaton HCM1A1305-R10-R 0.10 uH AEC-Q200 Inductor, 43 A

Share
Eaton HCM1A1305-R10-R: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 43 A Irms, Isat 80 A, DCR 0.52 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1A1305-R10-R 0.10 uH AEC-Q200 Inductor, 43 A

    HCM1A1305-R10-R at a glance: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 43 A Irms, Isat 80 A (20% rolloff @ +25 °C), DCR 0.52 mOhm, 13.8 x 12.5 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1305-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.064 uH
    Irms (DC, 40 °C rise)43 A
    Isat (20% rolloff @ +25 °C)80 A
    DCR typical @ +20 °C0.52 mOhm
    DCR maximum @ +20 °C0.59 mOhm
    K-factor (Bp-p = K x L x dI)818, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10551

    Dimensions and Pad Layout

    HCM1A1305-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10551: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 43 A the winding dissipates about 0.961 W in copper alone, using the typical DCR of 0.52 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 320 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 818, a peak-to-peak ripple of one amp produces roughly 81.8 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1305 family this is value 1 of 23, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCM1A1305-R22-R, sits at 0.22 uH with 40 A and 0.63 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.59 mOhm becomes roughly 0.903 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products