Eaton HCM1A1305-R47-R 0.47 uH Automotive Power Inductor
Eaton HCM1A1305-R47-R 0.47 uH Automotive Power Inductor

Eaton HCM1A1305-R47-R 0.47 uH Automotive Power Inductor

Share
Eaton HCM1A1305-R47-R: AEC-Q200 automotive power inductor, 0.47 uH ±20%, 33 A Irms, Isat 36 A, DCR 0.8 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1A1305-R47-R 0.47 uH Automotive Power Inductor

    HCM1A1305-R47-R at a glance: AEC-Q200 automotive power inductor, 0.47 uH ±20%, 33 A Irms, Isat 36 A (20% rolloff @ +25 °C), DCR 0.8 mOhm, 13.8 x 12.5 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1305-R47-R
    OCL (open circuit inductance)0.47 uH ±20%
    FLL minimum, at Isat0.3 uH
    Irms (DC, 40 °C rise)33 A
    Isat (20% rolloff @ +25 °C)36 A
    DCR typical @ +20 °C0.8 mOhm
    DCR maximum @ +20 °C0.92 mOhm
    K-factor (Bp-p = K x L x dI)375, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10551

    Outline Drawing

    HCM1A1305-R47-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10551: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 0.8 mOhm typical, the I-squared-R loss at the full 33 A rating is about 0.871 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 305 uJ, the number that connects the inductance and the current rating into a single transient figure.

    With K = 375, a peak-to-peak ripple of one amp produces roughly 176 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1305 family this is value 4 of 23, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A1305-R56-R, gives 0.56 uH at 28 A and DCR 1.15 mOhm: the extra inductance costs about 7 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.92 mOhm becomes roughly 1.41 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products