Eaton HCM1A1305-R68-R 0.68 uH Shielded Automotive Inductor
Eaton HCM1A1305-R68-R 0.68 uH Shielded Automotive Inductor

Eaton HCM1A1305-R68-R 0.68 uH Shielded Automotive Inductor

Share
Eaton HCM1A1305-R68-R: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 27 A Irms, Isat 32 A, DCR 1.15 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCM1A1305-R68-R 0.68 uH Shielded Automotive Inductor

    HCM1A1305-R68-R at a glance: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 27 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 1.15 mOhm, 13.8 x 12.5 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1305-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.44 uH
    Irms (DC, 40 °C rise)27 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C1.15 mOhm
    DCR maximum @ +20 °C1.33 mOhm
    K-factor (Bp-p = K x L x dI)263, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10551

    Mechanical Dimensions & Pad Layout

    HCM1A1305-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10551: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 27 A the winding dissipates about 0.838 W in copper alone, using the typical DCR of 1.15 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 348 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 263 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 179 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1305 line-up this part is number 6 of 23 by inductance, between 0.1 uH and 33 uH.

    Compared with its neighbours in the table, HCM1A1305-R82-R trades 2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.33 mOhm becomes roughly 2.04 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products