Eaton HCM1A1305V2-220-R AEC-Q200 Inductor 22 uH, Isat 7 A
Eaton HCM1A1305V2-220-R AEC-Q200 Inductor 22 uH, Isat 7 A

Eaton HCM1A1305V2-220-R AEC-Q200 Inductor 22 uH, Isat 7 A

Share
Eaton HCM1A1305V2-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 5 A Irms, Isat 7 A, DCR 34.7 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V2-220-R AEC-Q200 Inductor 22 uH, Isat 7 A

    HCM1A1305V2-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 5 A Irms, Isat 7 A (20% rolloff @ +25 °C), DCR 34.7 mOhm, 13.8 x 12.9 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1305V2-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)5 A
    Isat (20% rolloff @ +25 °C)7 A
    DCR typical @ +20 °C34.7 mOhm
    DCR maximum @ +20 °C40 mOhm
    SRF typical5 MHz
    K-factor (Bp-p = K x L x dI)50, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10904

    Mechanical Dimensions & Pad Layout

    HCM1A1305V2-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10904: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    Copper loss at the rated current works out to roughly 0.868 W from a typical DCR of 34.7 mOhm at 5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 539 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 50 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,100 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1305V2 family this is value 22 of 23, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A1305V2-330-R, gives 33 uH at 4.5 A and DCR 49.2 mOhm: the extra inductance costs about 2 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 40 mOhm becomes roughly 61.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products