Eaton HCM1A1305V3-220-R 22 uH Automotive Power Inductor
Eaton HCM1A1305V3-220-R 22 uH Automotive Power Inductor

Eaton HCM1A1305V3-220-R 22 uH Automotive Power Inductor

Share
Eaton HCM1A1305V3-220-R: AEC-Q200 automotive power inductor, 22 uH ±20%, 5 A Irms, Isat 7 A, DCR 34.7 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-220-R 22 uH Automotive Power Inductor

    HCM1A1305V3-220-R at a glance: AEC-Q200 automotive power inductor, 22 uH ±20%, 5 A Irms, Isat 7 A (20% rolloff @ +25 °C), DCR 34.7 mOhm, 13.8 x 12.9 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1305V3-220-R
    OCL (open circuit inductance)22 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)5 A
    Isat (20% rolloff @ +25 °C)7 A
    DCR typical @ +20 °C34.7 mOhm
    DCR maximum @ +20 °C40 mOhm
    SRF typical5 MHz
    K-factor (Bp-p = K x L x dI)39, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Mechanical Dimensions & Pad Layout

    HCM1A1305V3-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    Copper loss at the rated current works out to roughly 0.869 W from a typical DCR of 34.7 mOhm at 5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 539 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 39 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 858 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1305V3 family spans 0.1 uH to 33 uH; this row sits at position 22 of 23.

    One step down the table, HCM1A1305V3-150-R, sits at 15 uH with 6.5 A and 23.5 mOhm – the lower inductance buys about 2 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 40 mOhm becomes roughly 61.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products