Eaton HCM1A1305V3-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 18 A
Eaton HCM1A1305V3-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 18 A

Eaton HCM1A1305V3-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 18 A

Share
Eaton HCM1A1305V3-4R7-R: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 11 A Irms, Isat 18 A, DCR 8.15 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 18 A

    HCM1A1305V3-4R7-R at a glance: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 11 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 8.15 mOhm, 13.8 x 12.9 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1305V3-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3.01 uH
    Irms (DC, 40 °C rise)11 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C8.15 mOhm
    DCR maximum @ +20 °C9.38 mOhm
    SRF typical13 MHz
    K-factor (Bp-p = K x L x dI)105, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Mechanical Dimensions & Pad Layout

    HCM1A1305V3-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 8.15 mOhm typical, the I-squared-R loss at the full 11 A rating is about 0.986 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 761 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 105 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 494 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 13 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1305V3 family spans 0.1 uH to 33 uH; this row sits at position 13 of 23.

    One step down the table, HCM1A1305V3-3R3-R, sits at 3.3 uH with 12 A and 5.75 mOhm – the lower inductance buys about 2 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 9.38 mOhm becomes roughly 14.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products