Eaton HCM1A1305V3-5R6-R 5.6 uH Automotive Power Inductor
Eaton HCM1A1305V3-5R6-R 5.6 uH Automotive Power Inductor

Eaton HCM1A1305V3-5R6-R 5.6 uH Automotive Power Inductor

Share
Eaton HCM1A1305V3-5R6-R: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 10 A Irms, Isat 17 A, DCR 11 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-5R6-R 5.6 uH Automotive Power Inductor

    HCM1A1305V3-5R6-R at a glance: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 10 A Irms, Isat 17 A (20% rolloff @ +25 °C), DCR 11 mOhm, 13.8 x 12.9 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1305V3-5R6-R
    OCL (open circuit inductance)5.6 uH ±20%
    FLL minimum, at Isat3.58 uH
    Irms (DC, 40 °C rise)10 A
    Isat (20% rolloff @ +25 °C)17 A
    DCR typical @ +20 °C11 mOhm
    DCR maximum @ +20 °C12.7 mOhm
    SRF typical11 MHz
    K-factor (Bp-p = K x L x dI)87, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Mechanical Dimensions & Pad Layout

    HCM1A1305V3-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 1.1 W from a typical DCR of 11 mOhm at 10 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 809 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 87 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 487 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 11 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1305V3 family spans 0.1 uH to 33 uH; this row sits at position 14 of 23.

    Compared with its neighbours in the table, HCM1A1305V3-6R0-R trades 1.3 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 12.7 mOhm becomes roughly 19.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products