Eaton HCM1A1305V3-6R8-R 6.8 uH Shielded Automotive Inductor
Eaton HCM1A1305V3-6R8-R 6.8 uH Shielded Automotive Inductor

Eaton HCM1A1305V3-6R8-R 6.8 uH Shielded Automotive Inductor

Share
Eaton HCM1A1305V3-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 9.5 A Irms, Isat 15 A, DCR 12.1 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-6R8-R 6.8 uH Shielded Automotive Inductor

    HCM1A1305V3-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 9.5 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 12.1 mOhm, 13.8 x 12.9 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1305V3-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)9.5 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C12.1 mOhm
    DCR maximum @ +20 °C14 mOhm
    SRF typical11 MHz
    K-factor (Bp-p = K x L x dI)111, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Outline Drawing

    HCM1A1305V3-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 9.5 A the winding dissipates about 1.09 W in copper alone, using the typical DCR of 12.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Energy storage at the saturation current is around 765 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 111 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 755 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 11 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1305V3 family this is value 16 of 23, in a range that runs from 0.1 uH to 33 uH.

    The next value up in the same family, HCM1A1305V3-7R8-R, gives 7.8 uH at 7.6 A and DCR 15 mOhm: the extra inductance costs about 2.1 A of rated current.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 14 mOhm becomes roughly 21.4 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the qualification and the mounting process match the assembly line.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products