Eaton HCM1A1305V3-7R8-R AEC-Q200 Inductor 7.8 uH, Isat 15 A
Eaton HCM1A1305V3-7R8-R AEC-Q200 Inductor 7.8 uH, Isat 15 A

Eaton HCM1A1305V3-7R8-R AEC-Q200 Inductor 7.8 uH, Isat 15 A

Share
Eaton HCM1A1305V3-7R8-R: AEC-Q200 automotive power inductor, 7.8 uH ±20%, 7.6 A Irms, Isat 15 A, DCR 15 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1305V3-7R8-R AEC-Q200 Inductor 7.8 uH, Isat 15 A

    HCM1A1305V3-7R8-R at a glance: AEC-Q200 automotive power inductor, 7.8 uH ±20%, 7.6 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 15 mOhm, 13.8 x 12.9 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1305V3-7R8-R
    OCL (open circuit inductance)7.8 uH ±20%
    FLL minimum, at Isat4.99 uH
    Irms (DC, 40 °C rise)7.6 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C15 mOhm
    DCR maximum @ +20 °C17.3 mOhm
    SRF typical10 MHz
    K-factor (Bp-p = K x L x dI)79, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1488

    Mechanical Drawing

    HCM1A1305V3-7R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1488: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    Copper loss at the rated current works out to roughly 0.869 W from a typical DCR of 15 mOhm at 7.6 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 878 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 79 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 616 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 10 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1305V3 line-up this part is number 17 of 23 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCM1A1305V3-6R8-R, sits at 6.8 uH with 9.5 A and 12.1 mOhm – the lower inductance buys about 2 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 17.3 mOhm becomes roughly 26.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message