
| Parameter | Value |
|---|---|
| Orderable part number | HCM1A1305V3-R10-R |
| OCL (open circuit inductance) | 0.10 uH ±20% |
| FLL minimum, at Isat | 0.064 uH |
| Irms (DC, 40 °C rise) | 43 A |
| Isat (20% rolloff @ +25 °C) | 80 A |
| DCR typical @ +20 °C | 0.33 mOhm |
| DCR maximum @ +20 °C | 0.59 mOhm |
| SRF typical | 234 MHz |
| K-factor (Bp-p = K x L x dI) | 1,190, Bp-p in Gauss |
| Package | 13.8 x 12.9 mm |
| Height | 5.0 mm |
| Mounting | Surface mount |
| Operating temperature | -55 °C to +155 °C (ambient plus self-heating) |
| Qualification | AEC-Q200 |
| RoHS | Compliant, -R suffix |
| Data sheet | Eaton Technical Data ELX1488 |

Drawing reproduced from Eaton Technical Data ELX1488: outline with
rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
the drawing itself.
Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.
With 0.33 mOhm typical, the I-squared-R loss at the full 43 A rating is about 0.61 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.
Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.
Stored energy at Isat is about 320 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.
The K-factor of 1,190 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 119 Gauss of Bp-p, the figure the core-loss curve is plotted against.
Self-resonant frequency is 234 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.
The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.
In the HCM1A1305V3 line-up this part is number 1 of 23 by inductance, between 0.1 uH and 33 uH.
Compared with its neighbours in the table, HCM1A1305V3-R22-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.
Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.59 mOhm becomes roughly 0.903 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.
Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.
Is the part shielded for ADAS modules?
The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.
What is the self-resonant frequency used for?
It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.
What does AEC-Q200 cover?
The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd