Eaton HCM1A1307-100-R 10 uH AEC-Q200 Inductor, 6.3 A
Eaton HCM1A1307-100-R 10 uH AEC-Q200 Inductor, 6.3 A

Eaton HCM1A1307-100-R 10 uH AEC-Q200 Inductor, 6.3 A

Share
Eaton HCM1A1307-100-R: AEC-Q200 automotive power inductor, 10 uH ±20%, 6.3 A Irms, Isat 12 A, DCR 15.5 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-100-R 10 uH AEC-Q200 Inductor, 6.3 A

    HCM1A1307-100-R at a glance: AEC-Q200 automotive power inductor, 10 uH ±20%, 6.3 A Irms, Isat 12 A (20% rolloff @ +25 °C), DCR 15.5 mOhm, 13.7 x 13 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1307-100-R
    OCL (open circuit inductance)10 uH ±20%
    FLL minimum, at Isat6.4 uH
    Irms (DC, 40 °C rise)6.3 A
    Isat (20% rolloff @ +25 °C)12 A
    DCR typical @ +20 °C15.5 mOhm
    DCR maximum @ +20 °C17.5 mOhm
    K-factor (Bp-p = K x L x dI)40, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Dimensions and Pad Layout

    HCM1A1307-100-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 15.5 mOhm is what sets the efficiency: at 6.3 A the winding drops about 0.098 mV and dissipates 0.615 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 720 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 40, a peak-to-peak ripple of one amp produces roughly 400 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A1307, this is the 15th, in a family covering 0.22 uH to 56 uH.

    Compared with its neighbours in the table, HCM1A1307-120-R trades 2.1 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 17.5 mOhm becomes roughly 26.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message