Eaton HCM1A1307-560-R 56 uH Shielded Automotive Inductor
Eaton HCM1A1307-560-R 56 uH Shielded Automotive Inductor

Eaton HCM1A1307-560-R 56 uH Shielded Automotive Inductor

Share
Eaton HCM1A1307-560-R: AEC-Q200 automotive power inductor, 56 uH ±20%, 4.6 A Irms, Isat 4.6 A, DCR 55 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-560-R 56 uH Shielded Automotive Inductor

    HCM1A1307-560-R at a glance: AEC-Q200 automotive power inductor, 56 uH ±20%, 4.6 A Irms, Isat 4.6 A (20% rolloff @ +25 °C), DCR 55 mOhm, 13.7 x 13 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1307-560-R
    OCL (open circuit inductance)56 uH ±20%
    FLL minimum, at Isat35.8 uH
    Irms (DC, 40 °C rise)4.6 A
    Isat (20% rolloff @ +25 °C)4.6 A
    DCR typical @ +20 °C55 mOhm
    DCR maximum @ +20 °C65 mOhm
    K-factor (Bp-p = K x L x dI)18, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Mechanical Drawing

    HCM1A1307-560-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    The DCR figure of 55 mOhm is what sets the efficiency: at 4.6 A the winding drops about 0.253 mV and dissipates 1.16 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 592 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 18 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,008 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1307 line-up this part is number 20 of 20 by inductance, between 0.22 uH and 56 uH.

    Compared with its neighbours in the table, HCM1A1307-330-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 65 mOhm becomes roughly 99.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products