Eaton HCM1A1307-8R2-R 8.2 uH Automotive Power Inductor
Eaton HCM1A1307-8R2-R 8.2 uH Automotive Power Inductor

Eaton HCM1A1307-8R2-R 8.2 uH Automotive Power Inductor

Share
Eaton HCM1A1307-8R2-R: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 8.2 A Irms, Isat 13 A, DCR 11.5 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-8R2-R 8.2 uH Automotive Power Inductor

    HCM1A1307-8R2-R at a glance: AEC-Q200 automotive power inductor, 8.2 uH ±20%, 8.2 A Irms, Isat 13 A (20% rolloff @ +25 °C), DCR 11.5 mOhm, 13.7 x 13 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1307-8R2-R
    OCL (open circuit inductance)8.2 uH ±20%
    FLL minimum, at Isat5.25 uH
    Irms (DC, 40 °C rise)8.2 A
    Isat (20% rolloff @ +25 °C)13 A
    DCR typical @ +20 °C11.5 mOhm
    DCR maximum @ +20 °C13 mOhm
    K-factor (Bp-p = K x L x dI)47, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Outline Drawing

    HCM1A1307-8R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    At the rated 8.2 A the winding dissipates about 0.773 W in copper alone, using the typical DCR of 11.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 693 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 47 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 385 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1307 family spans 0.22 uH to 56 uH; this row sits at position 14 of 20.

    One step down the table, HCM1A1307-7R8-R, sits at 7.8 uH with 8.8 A and 10 mOhm – the lower inductance buys about 2.5 A of extra current in the same body.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 13 mOhm becomes roughly 19.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Verify the part marking for revision traceability in production.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products