Eaton HCM1A1307-R22-R AEC-Q200 Inductor 0.22 uH, Isat 100 A
Eaton HCM1A1307-R22-R AEC-Q200 Inductor 0.22 uH, Isat 100 A

Eaton HCM1A1307-R22-R AEC-Q200 Inductor 0.22 uH, Isat 100 A

Share
Eaton HCM1A1307-R22-R: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 48 A Irms, Isat 100 A, DCR 0.58 mOhm, 13.7 x 13 mm.
    • Product Details
    • Download

    Eaton HCM1A1307-R22-R AEC-Q200 Inductor 0.22 uH, Isat 100 A

    HCM1A1307-R22-R at a glance: AEC-Q200 automotive power inductor, 0.22 uH ±20%, 48 A Irms, Isat 100 A (20% rolloff @ +25 °C), DCR 0.58 mOhm, 13.7 x 13 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A1307-R22-R
    OCL (open circuit inductance)0.22 uH ±20%
    FLL minimum, at Isat0.14 uH
    Irms (DC, 40 °C rise)48 A
    Isat (20% rolloff @ +25 °C)100 A
    DCR typical @ +20 °C0.58 mOhm
    DCR maximum @ +20 °C0.7 mOhm
    K-factor (Bp-p = K x L x dI)261, Bp-p in Gauss
    Package13.7 x 13 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10552

    Mechanical Drawing

    HCM1A1307-R22-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10552: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 0.58 mOhm is what sets the efficiency: at 48 A the winding drops about 0.028 mV and dissipates 1.34 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 1,100 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 261 means the flux swing is about 57.4 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1307 family this is value 1 of 20, in a range that runs from 0.22 uH to 56 uH.

    Compared with its neighbours in the table, HCM1A1307-R33-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.7 x 13 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.7 mOhm becomes roughly 1.07 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products