Eaton HCM1A1307V2-1R5-R 1.5 uH Automotive Power Inductor
Eaton HCM1A1307V2-1R5-R 1.5 uH Automotive Power Inductor

Eaton HCM1A1307V2-1R5-R 1.5 uH Automotive Power Inductor

Share
Eaton HCM1A1307V2-1R5-R: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 21 A Irms, Isat 25 A, DCR 2.04 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V2-1R5-R 1.5 uH Automotive Power Inductor

    HCM1A1307V2-1R5-R at a glance: AEC-Q200 automotive power inductor, 1.5 uH ±20%, 21 A Irms, Isat 25 A (20% rolloff @ +25 °C), DCR 2.04 mOhm, 13.8 x 12.9 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1307V2-1R5-R
    OCL (open circuit inductance)1.5 uH ±20%
    FLL minimum, at Isat0.96 uH
    Irms (DC, 40 °C rise)21 A
    Isat (20% rolloff @ +25 °C)25 A
    DCR typical @ +20 °C2.04 mOhm
    DCR maximum @ +20 °C2.4 mOhm
    SRF typical31 MHz
    K-factor (Bp-p = K x L x dI)126, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10905

    Dimensions and Pad Layout

    HCM1A1307V2-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10905: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 2.04 mOhm typical, the I-squared-R loss at the full 21 A rating is about 0.9 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    At Isat the part holds about 469 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 126 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 189 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 31 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1307V2 family this is value 6 of 20, in a range that runs from 0.22 uH to 56 uH.

    One step down the table, HCM1A1307V2-1R2-R, sits at 1.2 uH with 22.5 A and 1.78 mOhm – the lower inductance buys about 3.5 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.4 mOhm becomes roughly 3.67 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products